When Using a USB, what is the WB45 Ethernet/ Wi-Fi Bridge Mode Firmware Upgrade Procedure?

After storing the files in USB storage, plug the USB storage into the USB port on the WB45 breakout board

Type the following commands to upgrade via the USB interface:

Summit Data Communications

summit login: root

Password:

#

#

# /etc/init.d/opt/S91g_ether stop

Disabling USB gadget ethernet

# /etc/init.d/opt/S37usbhost start

Enabling USB host-mode for Mass Storage

# sd 0:0:0:0: [sda] No Caching mode page present

sd 0:0:0:0: [sda] Assuming drive cache: write through

sd 0:0:0:0: [sda] No Caching mode page present

sd 0:0:0:0: [sda] Assuming drive cache: write through

sd 0:0:0:0: [sda] No Caching mode page present

sd 0:0:0:0: [sda] Assuming drive cache: write through

# cd /media/usb0/

# cd wb45n-laird_fips-3.4.1.106/

# ls

bootstrap.bin  fw_select      kernel.bin     u-boot.bin

fw.txt         fw_update      rootfs.bin

# ./fw_update

Accessing images via locally attached media.

# wb45nbt update

Checking Bootstrap Loader...OK

Updating bootstrap from local...    à Choose Yes

  /media/usb0/wb45n-laird_fips-3.4.1.106/bootstrap.bin

  erasing, writing...(0s) OK

Checking U-Boot Loader... OK

Updating bootloader from local...    à Choose Yes

  /media/usb0/wb45n-laird_fips-3.4.1.106/u-boot.bin

  erasing, writing...(0s) OK

Checking Linux Kernel...

Updating kernel-a from local...    à Choose Yes

  /media/usb0/wb45n-laird_fips-3.4.1.106/kernel.bin

  erasing, writing...(1s) OK

Checking Root Filesystem...

Updating rootfs-a from local...    à Choose No

  /media/usb0/wb45n-laird_fips-3.4.1.106/rootfs.bin

  erasing, writing...(12s) OK

Sync'ing updated_% at91bs=x u_boot=x kernel=a rootfs=a

Done.

fw_select v20130313

Stopping LigHTTPd

Stopping inetd services.

Stopping network interfaces... wl eth0 lo

Stopping system message bus: done

Saving random seed... done

Stopping execution of events, via udev...

Stopping logging services: syslogd klogd

The system is going down NOW!

Sent SIGTERM to all processes

RomBOOTGKILL tRestarting system.

 ba_offset = 0xb ...

Loading 1-Wire info...

Enumerate all roms:

Done, 0x0 1-wire chips found!

sn: 0x0;   rev: 0x0

AT91Bootstrap 3.4.4-laird2 ( Mon Apr 14 12:50:28 EDT 2014 )

Downloading image...

Nand: ONFI not supported

NAND device: NAND 128MiB 1,8V 8-bit, Manufacturer ID: 0x0 Chip ID: 0xa1

Nand: Copy 0x80000 bytes from 0x20000 to 0x23f00000

Done!

 U-Boot 2013.01-laird2 (Apr 14 2014 - 12:50:30)

CPU: AT91SAM9G25

Crystal frequency:       12 MHz

CPU clock        :      400 MHz

Master clock     :  133.333 MHz

DRAM:  64 MiB

WARNING: Caches not enabled

NAND:  128 MiB

MMC:   mci: 0

In:    serial

Out:   serial

Err:   serial

Net:   macb0

Hit any key to stop autoboot:  0

NAND read: device 0 offset 0xe0000, size 0x280000

 2621440 bytes read: OK

## Booting kernel from Legacy Image at 22000000 ...

   Image Name:   Linux-3.8.0-laird15

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    2150254 Bytes = 2.1 MiB

   Load Address: 20008000

   Entry Point:  20008000

   Verifying Checksum ... OK

   Loading Kernel Image ... OK

OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.

gluebi (pid 1): gluebi_resized: got update notification for unknown UBI device 0 volume 0

Starting logging services: syslogd klogd

Starting udev daemon, populating /dev

Initializing random number generator... done

Checking platform... wb45n-laird_fips-3.4.1.106

  updated bootstrap: (-?-)

  updated u-boot: (-?-)

  updated kernel-a (95fbed43d075ff3050e7e5bb00e632cb)

  updated rootfs-a (b4645e745a88e3cdf68b2749efecbd83)

Starting system message bus: done

Starting network interfaces... lo eth0 wl usb0

Starting inetd services...

  tftp is setting up...

  ssh is setting up...

  ftp is setting up...

Starting LigHTTPd

Summit Data Communications

summit login: