RM024 Series
Learn more and compare with similar parts on the family page.


Antenna Options
U.FL Jack
Antenna Type
42 selectable channels
Chipset (Wireless)
TI CC2510
Data Rate
280 kbps or 500 kbps selectable
Dimension (Height - mm)
3.6 mm
Dimension (Length - mm)
32.4 mm
Dimension (Width - mm)
25.4 mm
Frequency Range (Max)
2483 MHz
Frequency Range (Min)
2402 MHz
Input Power
2.3 - 3.6 V - 50 mV ripple
Logical Interfaces
Network Architecture
Configuration and Test Software
Output Power
10 mW
Power Consumption (Rx)
36 mA
Power Consumption (Tx)
40 mA
Product Type
Embedded Module
FHSS Wireless Protocol
Outdoor: 0.6 miles(1.0km). Indoor: 328 ft(100m)
Receive Sensitivity
-95 dBm at 280 kbps RF Data Rate
Laird Configuration Utility
System Architecture
Proprietary RF (2.4 GHz)
Transmit Power (Max)
+3.5 to +10 dBm
Wireless Specification
2.4 GHz FHSS

Buy Now

Distributor Part In Stock Region Buy
DigiKey RM024-P10-C-30 1779 North America Buy Now
Jak Electronics RM024-P10-C-30 753 APAC Buy Now
Mouser RM024-P10-C-30 687 North America Buy Now
Farnell RM024-P10-C-30 348 EMEA Buy Now
Newark RM024-P10-C-30 168 North America Buy Now
element14 APAC RM024-P10-C-30 168 APAC Buy Now
Avnet RM024-P10-C-30 0 North America Buy Now
Symmetry Electronics RM024-P10-C-30 0 North America Buy Now


What can I do to minimize current consumption and optimize battery life in my LT1110/RM024 application?

The RM024 and LT1110 provide a couple of options for reducing power consumption for applications which will required the radio to operate on battery power:


  1. Cyclic Sleep Mode can be enabled on a client radio which causes the radio to sleep for a programmable period of time and wake for a programmable period of time. For additional information see the Application Note: Cyclic Sleep Mode available from the RM024 Product Page. While there is currently not an Application Note written specifically for the LT1110, the process is the same for both modules so the RM024 Cyclic Sleep App Note can be referenced for both modules.
  2. Deep Sleep Modes (PM2 & PM3): The OEM host can issue the Enter Deep Sleep Command, as outlined in the modules User Guide to minimize current draw: RM024 User Guide - Section 4.2.3 Enter Deep Sleep LT1110 User Guide - Utility Commands Section - Deep Sleep


While in Deep Sleep Mode the processor has all interfaces disabled, including RF and Serial. Two sleep modes are supported: PM2, and PM3:

  • PM2: The radio can either be awakened by the Sleep Interrupt Pin (Force 9600), by a Hard Reset, or when the sleep timer, which is configured with the command, expires.
  • PM3: The module can only be awakened by the Sleep Interrupt pin (Force 9600). The sleep timer is not active in PM3 and the bytes controlling the timer are disregarded and can be omitted from the command.


Additional considerations for maximizing battery life:

  • Adding power control so you can programmatically disable VCC to the radio.
  • Consider reducing the transmit power - test with lower transmit powers in sites typical of end user experience to see if this is an option.
  • Where applicable, consider buffering data to create larger packets of RF data rather than sending several smaller packets. 
  • Holding the processor in Reset using the Reset pin will NOT enable a Low Power Mode


What is Laird Connectivity's product lifecycle EOL and PCN policy?

Laird Connectivity is committed to the long-term supply of all its standard embedded wireless modules and packaged products. Laird Connectivity’s products are specifically designed to meet the needs of the industrial and medical markets, which typically require 7 – 10 years product lifecycle. Although Laird Connectivity can’t guarantee that a component used in our products will not be obsoleted and cannot be reasonably substituted, Laird Connectivity can assure customers we will continue to sell our product when we have customer demand and can obtain the necessary components to build our products.

View our full policy here.